Tablestacas are sometimes made by the AZ28 and AZ 28 inclusion of an arbitrary horizontal force such as 50 to 100 tons. When the spacing of the mooring posts is known, an evaluation of moor post pull on the structure can be made. On the menu bar, click Soil and then choose Materials to open the input window. In this window, the names and properties of the soil materials can be entered.(b) Tie rod yield strength. The AZ 38 tie rod yield strength is the product of A net times fy for steel rods and A net times minimum yield strength for aluminum rods. The design capacity of the AZ38 anchor wall or deadman, should be sufficient to develop the tie rod yield strength. Specify the AZ28 names of the soil materials in the left-hand table. The soil materials entered here can be connected to their geometry using the Soil Profiles input window. The effect of downward seepage in the soil behind the piling is very small and may be elected. Tie rod support. The tie rod design is based on the assumption that the rod is straight and centrically loaded.
Tablestacas must be anticipated that AZ34 or AZ 34 will occur through interlocks, although the mount is difficult to predict. For Single pile model, the content of the Soil Materials window depends on the loading type:For loading by forces and by user-defined soil displacements, the General soil parameters, the Earth pressure coefficients and the Modulus of subgrade reaction must be specified for each material. The tie rod must also be protected against any potential consolidation in the A 28 backfill. As an approximation, the seepage should be assumed to qual at least 0.025 gallons per minute per square foot of wall per foot of net head across he wall for installations in moderately to highly permeable soils. Careful attention must be directed to the tie rod-to-wale connection and tie rod-to-anchor connection to eliminate any eccentricities at these points.
The geotechnical engineer should evaluate any potential settlement due to consolidation and the tie rod should be encased in a conduit of sufficient diameter to permit AZ36 backfill consolidation without contact between the rod and conduit. In addition to the lateral pressures described previously, Tablestacas structures may be subjected to some of the AZ 36 lateral loads described below. The rod must be protected against any influence which tends to induce bending in the rod. For loading by calculated soil displacements, only the General soil parameters must be specified for each material. Ship impact - AZ34 Tablestacas dock and waterfront structures may often be subjected to the direct impact of a moving ship. Note: When using the Brinch-Hansen method the same soil material should not be used at different depths in a soil profile.
The magnitude of the mooring pull in the direction of the ship may be taken as the winch capacity used on the ship. Instead AZ36 and AZ 36 should be made, with a different name. Ice Thrust - Lateral thrusts can be caused by the volume expansion of ice in ne-grained soils (very fine sand, silt and clay). Rods used as tendons should be designed according to the preceding strength requirements for tie rods. The possibility of AZ 34 lateral thrust from ice or frozen ground should be eliminated by placing free-draining coarse granular soil above he frost line behind a Tablestacas wall. Steel Tablestacas also offers the advantage that it an yield laterally to relieve any thrust load due to ice. Tendons for grouted anchors may be either rods or cables. Wave Forces - There are many theories concerning wave pressure against a vertical surface. When cables are used, the size should be evaluated based on manufacturer’s specifications for the sum of the anchor force and any alignment loads. In general, wave pressure is a function of wave height, length, velocity and many other AZ36 factors. Note: Active and neutral earth pressure coefficients normally need to be set to zero for the situation of a single pile loaded by soil displacement. Design and Construction of AZ 34 Ports and Marine Structures by Alonzo DeF.
Quinn, Substructure Analysis and Design by Paul Anderson, AZ36 pile Foundations by Robert D.Chellis and Shore Protection, Planning and Design, TR No. 4 Dept. of the Army, Corps of Engineers. This means that the input value for the passive earth pressure coefficient leads to the effective resisting pressure, taking the effect of arching into account. Fender systems should be used in this case to spread out he reaction and reduce the impact to a minimum. AZ34 modulus of subgrade reaction: User-defined values for the modulus of subgrade reaction can be entered in this sub-window. For the design of retaining walls of moderate height, the lateral pressure for design may be increased by about 10 per cent. Alternatively, for a pile loaded by forces, D-Tablestacas can calculate the modulus of subgrade reaction according to Ménard’s theory.
AZ38 or AZ 38 dock and water front structures generally provide mooring posts for anchoring and docking ships. Wales which transfer the tie rod forces to the Tablestacas are usually composed of back-to-back channels. During an AZ 28 earthquake the vibration of the ground may temporarily increase the lateral pressure against a retaining structure. From a load transfer standpoint, the most desirable position of the wales is on the outside of the piling. This AZ 36 increase is a result of a number of factors including inertia force, direction, horizontal acceleration and period. When the wales are placed on the inside face, each individual AZ28 Tablestacas must be bolted to the wale.
The trial sliding wedge is assumed to be acted upon by a horizontal force in additional to all other forces. Some engineers assume that the horizontal force is equal to 18 to 33 percent of the weight of the sliding wedge. The wale is assumed to act as a continuous flexural member over simple supports at the tie rod locations. The designer, of course, should consider the location of the structure relative to previous A38 earthquake history. The maximum bending moment in the wale may be approximated as In the case of high retaining structures, the rial AZ 38 wedge method of analysis should be used.
+86-18018031808 
+86-18018031808